Difference between revisions of "Vespa Grande seat cover kit from Northwest Classic Seat Covers"

From Moped Wiki
Jump to: navigation, search
m (adding more pictures to tutorial)
m (Adding text to new page)
Line 10: Line 10:
  
 
[[Image:Old seat 002.JPG|600px|Junky seat]]
 
[[Image:Old seat 002.JPG|600px|Junky seat]]
 +
 +
 +
Most of the tools that I needed to install this seat cover kit are pictured below
  
 
[[Image:Seat recover 001.JPG|600px|tools needed]]
 
[[Image:Seat recover 001.JPG|600px|tools needed]]
 +
 +
 +
Quality contact cement is an absolute must. I use this brand for all my heavy duty bonding.<BR>
 +
I get this stuff in the paint section of Home Despot.
  
 
[[Image:Seat recover 002.JPG|600px|contact cement]]
 
[[Image:Seat recover 002.JPG|600px|contact cement]]
 +
 +
 +
To completely remove the old vinyl it is necessary to remove the aluminum decoration strip. It is held on by three rather fragile threaded clips secured by 1/4 inch nuts. If you just start twisting the nuts of with your 1/4" nut driver the could break off. Pre spray the threads with some lube.
  
 
[[image:Seat recover 003.JPG|600px|lube threads]]
 
[[image:Seat recover 003.JPG|600px|lube threads]]
 +
 +
 +
The passenges hold strap is held with m11 nuts and some fat washers. This one came apart nice because of the spray lube
  
 
[[image:Seat recover 004.JPG|600px|remove strap]]
 
[[image:Seat recover 004.JPG|600px|remove strap]]
 +
 +
 +
This next step is important as it will make probing for the for the molding holes through the new vinyl easy. Using your eye, line up a sharp tool so you can scratch a reference mark in the seat pan that will align with the location of the moldings holes.
  
 
[[image:Seat recover 005.JPG|600px|marking holes]]
 
[[image:Seat recover 005.JPG|600px|marking holes]]
 +
 +
 +
Since you pre soaked the threads with lube, your 1/4" nut driver will easily remove the fragile nuts
  
 
[[image:Seat recover 006.JPG|600px|molding nuts]]
 
[[image:Seat recover 006.JPG|600px|molding nuts]]
 +
 +
 +
Gently remove moldings.
  
 
[[image:Seat recover 007.JPG|600px|pull off molding]]
 
[[image:Seat recover 007.JPG|600px|pull off molding]]
 +
 +
 +
You will want to try to preserve the seat pans rubber edge welting. This will protect your new vinyl from the sharp edges of the pan.
  
 
[[image:Seat recover 008.JPG|600px|seat pan welting]]
 
[[image:Seat recover 008.JPG|600px|seat pan welting]]

Revision as of 11:55, 12 May 2019

Seem like every Vespa Grande bike I buy for restoration is of course plagued with a dried, cracked and ripped up vinyl seat. In the past I would shop on Buy Sell for a better looking option that when I got it in my hands can tell that the 40 year old seats vinyl was just a few ass plants away from also being split and cracked.
I had seen a vinyl kit advertised by for a while by Northwest Classic Seat Covers and finally decided to try one on my own personal bike.
It turned out so good and has held up so far for 6 months.

My Grande seat


Here is a link to where you can get this same kit from Northwest Classic Seat Covers
Now here is the seat of the latest bike I scored and is going to be the precipitant of the new vinyl kit.

Junky seat


Most of the tools that I needed to install this seat cover kit are pictured below

tools needed


Quality contact cement is an absolute must. I use this brand for all my heavy duty bonding.
I get this stuff in the paint section of Home Despot.

contact cement


To completely remove the old vinyl it is necessary to remove the aluminum decoration strip. It is held on by three rather fragile threaded clips secured by 1/4 inch nuts. If you just start twisting the nuts of with your 1/4" nut driver the could break off. Pre spray the threads with some lube.

lube threads


The passenges hold strap is held with m11 nuts and some fat washers. This one came apart nice because of the spray lube

remove strap


This next step is important as it will make probing for the for the molding holes through the new vinyl easy. Using your eye, line up a sharp tool so you can scratch a reference mark in the seat pan that will align with the location of the moldings holes.

marking holes


Since you pre soaked the threads with lube, your 1/4" nut driver will easily remove the fragile nuts

molding nuts


Gently remove moldings.

pull off molding


You will want to try to preserve the seat pans rubber edge welting. This will protect your new vinyl from the sharp edges of the pan.

seat pan welting

new vinyl kit

pre fitting

checking squareness

clamp the rear

sides even

clamp front

split vinyl

glue vinyl flap

tuck under cleat

glue front

streach and roll front

clamp

split edges

trim off excess

glue, stretch, tuck

superclamp

tuck in cleats

Wow! looks great

probe for holes

stab both sides

600px\slip in molding

nuts and washers

split strap for stud hole

wrench tight

leave slack

looks fantastic