Results 181–210 of 871
jm — 14 years ago
hi,i attached a new condenser externally as per mabecanes web page instructions , the moped runs with this new installment but i still need to take it on a longer trip than down the driveway to see if the original problem persist. as for those who suggested that it may be a clogged gas cap on the above mentioned longer trip if the problem persist ill loosen the cap to allow for air in the tank
jm — 14 years ago
hey Mabecane how are you? iwill the extra condensor you gave me work with external instalation?thanks
jm — 14 years ago
if you followed the link i have a question,if i want to connect the condenser externally, could i use tape instead of the female connector to attach the condenserthanks
jm — 14 years ago
just cut and pastehttp://mabecanemobylette.com/condenser_installation.htm
jm — 14 years ago
"mabecanemobylette.com/condenser_installation.htm":url
jm — 14 years ago
will this do the trick see link below"http://mabecanemobylette.com/condenser_installation.htm":url
jm — 14 years ago
well what i mean about bogging is that it runs great for a couple miles then it starts to run bad , it gets power then losses power intermittently and wants to die , i can drive it that way but it gets worse and worse it start to die more oftenlet me know what you thinkthanks
jm — 14 years ago
hi,i do have an extra condenser, how would i replace it though?oh,im not about to sell it right now sorrythanks
jm — 14 years ago
hi,i have a 78 motbecane vlx, i noticed when i take it out, it rides fine for around 5-6 miles then bogs down but if i give it a few minutes it will run fine again anyone have an idea what this is ? could it mean the gas is to old or what ?thanks
jm — 14 years ago
what the spring and the metal plat are on page 31 "spring" #5 and the "pulley spring limiter"#6http://staff.washington.edu/iet/Catalog.pdfit seems that the spring is housed in the limiter does this make sense? # 15thank you
jm — 14 years ago
hi,the other day i was driving home from work when i felt this vibrationfrom the engine area (i did have the vibration before on a regular basis, but not so strong, i thought it is normal for a ped to vibrate a bit) and then the ped died , i was able to start it again but when i gave it to much juice and the variator was at full tilt the vibration came back and the ped died again.so the symptoms
jm — 14 years ago
hi,i have a 78 motobecane vlx and i noticed grease/oil? that splatters on the pulley area ( that large flat plate like gear) and its coming out were the peddle crank is connected how is this stopped and y does this happen?thanks
jm — 14 years ago
make sure your not in a cold area
jm — 14 years ago
i believe it does
jm — 14 years ago
hi,i have 78 garelli euro flex it runs while on a kickstand but when i take it off the stand it turns off any ideas why ?thanks
jm — 14 years ago
where would i get cardboard gasket material?
jm — 14 years ago
http://www.dellortodirect.com/index.php?main_page=product_info&products_id=198
jm — 14 years ago
"http://www.dellortodirect.com/index.php?main_page=product_info&products_id=198 ":url
jm — 14 years ago
hi,i have a 14 12 Dellorto Carb, when i moved things around at the petcock and the fuel line to drain the gas tank, i noticed after that i had a fuel leak, i narrowed it down to either the fuel line doesn't have a proper seal on the nipple of the banjo or the seal of the banjo against the fuel filter and carb does not have a proper seal. one thing i also noticed the little washer called the &
jm — 14 years ago
how do you take off the fuel line? it seems to set on the petcock pretty secure .
jm — 14 years ago
hi,my tomos targa lx top tank has gas that has been sitting all winter, i would like to know the best way to remove the old gas.thank u
jm — 14 years ago
for now i am going to use the slightly bent axle untill i can get something to get the nut/cone off . i hope its ok, i mean i wonder how many years the person before me was riding it that way.
jm — 14 years ago
but i think the nut is stuck though
jm — 14 years ago
also need a vice
jm — 14 years ago
no, i didnt know it existed but now i need one.
jm — 14 years ago
hi,i want to replace an axle but i cant get the single nut and cone off the axle first of all there is nothing to grip (w/o damaging the axle) to counter the force to remove the nut and cone and second even when i use a vice grip it wont budge( i damaged the center of the axle that does that need a thread) any advice ?thanks
jm — 14 years ago
thank youi just came back from moped warehouse and they hooked me up with the parts i needed.
jm — 14 years ago
hi,i have a 78 vlx motobacane, i noticed when i was replacing the axle in the hub there was a rough spot in the spin, then i noticed that the axle was bent and this may be the culprit, is there any way of straighting out the axle without damaging it etc.thank you