Results 121–150 of 871
jm — 13 years ago
Hi,i was repairing my gurtner by replacing the screw that holds the throttle and choke slide in the carb, must have vibrated out? I noticed after replacing it when i turned the handle full throttle the slide did not completely clear the air passage about 1/8" to a 1/4". i adjusted the cable so it would clear. was i correct in doing so?thanks
jm — 13 years ago
can the level of the trans fluid be a factor?
jm — 13 years ago
is a clicking sound when 06 tomos shifts into 2nd gear normal?
jm — 13 years ago
Hi,i was going on a nice ride when i noticed my ped was going full throttle on its own. i looked at the carb and noticed the screw that holds the plate that clamps down the throttle slide/cable and the other cable springs in the carb was missing.i think the screw/washer is 14 and 15 in the diagram on the left(see link below). i believe its that carburetor since the air filter looks the same as mi
jm — 13 years ago
I have replaced the old condenser externaly,idealy you should cut the wire off the internal condensor for electrical reasons, but leave it in place since it will leavea hole if removed.also check your points clean/replace and check your timing as well.
jm — 13 years ago
the cap wire and plug are new
jm — 13 years ago
i think i was on the throttle but i dont remember , why?
jm — 13 years ago
the pop seems to come out the muffler not the carb?
jm — 13 years ago
i just replaced my spark plug and points just a day earlier, and noise im getting is like pop from the muffler and a reduction in power at the same time ?
jm — 13 years ago
i think you can stick any key in there and turn
jm — 13 years ago
also you should leave the old condenser in but disconnected with the wire cut off so you don't have a hole in that area.
jm — 13 years ago
just want to know if that's what im getting on my ped, also is it possible that it goes away on its own or just happens at certain speeds/rpm?thanks
jm — 13 years ago
that music came with the movie software off of my flip video cam
jm — 13 years ago
then why would anyone say not to clean a gurtner with carb cleaner but use kerasene?
jm — 13 years ago
i cleaned the carb last night, but without carb cleaner becouse i read some post that say its to harsh for the gurtner. after i cleaned it ran without the power loss issue but still has some "hickups" and the carb may need to be tuned better.
jm — 13 years ago
her is vid.http://video.google.com/videoplay?docid=1208952804915065364&hl=en
jm — 13 years ago
no, i bought it from mabecane around a year ago, just curious what would you pay for the vlx?
jm — 13 years ago
larry, you got me lol. but i have stopped buying anymore mopeds and started to work on the ones i have . your right i should have got a newer one to start.
jm — 13 years ago
yeah its the dirt bike one, i did make sure the coil was in tight but maybe i will look again.
jm — 13 years ago
i have a 78 motobecane vlx that runs fine when its on the stand but when i ride it on the road it has intermittent power loss i tried changing the condenser but that doesn't seem to be the problem,any suggestions?thank you
jm — 13 years ago
here is a vid of the seal ring that is coming out, how do i fix that and what coused it, maybe gas dripping?also if u are familiar w/jikov carbs you know where the fuel line connects to a brass nipple and the nipple is screwed in w/ a hollow screw my question is does the hole in the screw have to line up with the hole of the brass nipple ? becouse when i screw it in all the way it does not line up
jm — 13 years ago
hi,i unscrewed the nipple that the fuel line goes into, my questions is does the hole in the nipple have to line up with the hole in the screw, because when i replaced it, it doesn't seem to line up?thank you
jm — 13 years ago
here is a link to a video showing the domino throttle, im not certain how the throttle cable is installed. it seems that you may need a removable cable nipple to install it, but that seems crazy. let me know? oh this is for a jawa x20 and i think this handle came off a supreme jawa model.http://video.google.com/videoplay?docid=-8977677958871558872&hl=enthank u
jm — 13 years ago
how many teeth does the x 30 and x20 sprockets have ? and if i want an x 30 sprocket where would i get one?
jm — 13 years ago
now i need a throttle handle assembly, at the moment im just pulling the cable by hand, also is there a light switch because i cant find one if it means i need a new sealed beam headlight where can i get that and a bulb for the rear tail light?
jm — 13 years ago
thanks im such a fool i didnt us the de comp, i sprayed some starting fluid in the spark plug hole and i got her started thank you
jm — 13 years ago
thank you for your responce,1. i did check that, it was in the propper mode and that clutch cover/flywheel? thing turns slightly somtimes but for most part it doesnt turn.2. i believe i tried that, but could i pull off the cap and see if there is spark just in the wire?3. ok, ill look into that.i have a question on the gas tank it says to use SAE 90 for gear oil, does that make sense ?thank you