Results 31–60 of 871
J M — 11 years ago
Hi,I have been playing around with different jets but without great success, but when i ran it with out the air filter and box it seems to give the ped more muscle/speed does this mean i should hook up a high flow air filter and find the best jet that works with it?thank you
J M — 11 years ago
yess i am all stock beside the pipe
J M — 11 years ago
replaced the existing 52 jet in my del. 14:12 with a 60 jet and it seems my performance is worse any suggestions?thank you
J M — 11 years ago
I replaced the existing 52 jet on my Del. 14:12 with a 60 jet and it seems to have made the performance even worse any suggestions?
J M — 11 years ago
Hi,I just installed a weak ends pipe to my garelli eureka flex. It seems to get better low end albeit i only drove it up and down the block and i dont have a full scope of its capability's. but what would re jeting do? as it seems like the consensuses is you up jet with a new pipe.
J M — 11 years ago
Hi,I test ran the moped today for a short up and down the block. It seems that that there is increased low end but would re jeting also increase my high end?
J M — 11 years ago
i was able to drill an additional hole in the existing bracket to line up with the mope bracket so now i have at least one bolt holding the muffler
J M — 11 years ago
OK, I bent the peddle arm and it clears the pipe but now the problem is the mounting bracket holes doesnt line up with the frame? any suggestions?
J M — 11 years ago
Hi again,i bent the peddle it clears the pipe but now the mounting holes do not align, any suggestions?thank u
J M — 11 years ago
ok i got the peddle arm off. now the actual peddle is giving me trouble is it by chance reverse thread? also if i used a press instead of the ol pipe torch vice should i bother taking the peddle off the arm?
J M — 11 years ago
Hi,I have a vice but no torch or pipe to bend the pedal arm. can i bend the peddle arm with out torching it if i manage to find a pipe?
J M — 11 years ago
that is what i meant. by the way what is a goot way of getting the cotter pin off?
J M — 11 years ago
what method did you use to get the crank off and what method did you use to bend the crank?
J M — 11 years ago
how many of you have peddle clearance issues?
J M — 11 years ago
I took off the bolt on one side of the crank but im not certain how to pull it off after that.
J M — 11 years ago
I just tried to install the pipe, it seems that my peddle will not clear it with out bending also i may have to devise an extension bracket of sorts to get it mount properly. Any suggestion on how to remove and bend the pedal crank?
J M — 11 years ago
I want to install the weak-ends pipe on my Garelli but before i get started i had a few questions.1) do i need any kind of gasket between the pipe and where it gets bolted on to? or is there a gasket from the original pipe i can reuse?2) can i use the bolts the ped came with to install it both on the side bracket and where it hooks up to the engine?thank you
J M — 11 years ago
I just tried to install the pipe, it seems that my peddle will not clear it with out bending also i may have to devise an extension bracket of sorts to get it mount properly. Any suggestion on how to remove and bend the pedal crank?
J M — 11 years ago
Hi,I want to install the weak-ends pipe on my Garelli but before i get started i had a few questions.1) do i need any kind of gasket between the pipe and where it gets bolted on to? or is there a gasket from the original pipe i can reuse?2) can i use the bolts the ped came with to install it both on the side bracket and where it hooks up to the engine?thank you
J M — 11 years ago
I believe i have the ngk cap and the internal condenser is removed.
J M — 11 years ago
Hi,It seems that after i run the motobecane for around 10 to 15 min. it dies. when i wait another 10 min it starts up again. I changed the condenser and it does the same. do you think it may be the points ?thank you
J M — 11 years ago
any particular hi flow filter?
J M — 11 years ago
yes, everything is stock, except the original 14;12 was changed out for a different 14;12
J M — 11 years ago
Hi,I want to get a weak-ends pipe for my Garelli I have a 14;12 carb, what jets should i get and what range should i have to get my ped running smooth.Thank you,
J M — 11 years ago
what does the siding have to do with taxes?
J M — 11 years ago
what does soft seize and holed the piston mean?
J M — 11 years ago
as to running rich,I'm not 100 percent sure but i may have put twice the amount of oil, once at the gas station and once before i put the gas in my tank the next morning.As to the loose/broken part, it seems that im replacing missing screws more often, maybe i should look for something that is loose/broken. but I have one question, why would the ped start up again the next morning if somethi
J M — 11 years ago
what external condenser should i use and where sould i get it?