Results 31–60 of 6861
pat splat — 7 weeks ago
Prep crank and change out that seal ok.
pat splat — 7 weeks ago
On an air cooled ciao theres a path for cool air to go up cylinder around top and back down, if you were missing that tin piece thats on top it could sieze on idle.I use a mini sledge hammer and a wood dowel. Wood wedges help lift cylinder up, pound in.Post picts
pat splat — 7 weeks ago
Jetting matters. Stock w mesh air filter around 54. Two stroke oil matters too. Premix?Its either flooded or lean, check plug.
pat splat — 7 weeks ago
Heres some basics when you pull the cover off.Take notes/picts.Clutch bell spins independant of crank.Nothing should be binded.Theres a one way bearing in your countershaft.Peanut spring must be located in slot.Outside tranny.Theres a washer spring combo on pedal shaft.Rear brake stop gotta be in frame slot.Did it run shift fine before?Picts help
pat splat — 7 weeks ago
Or trade for a rear vespa variated clutch n hub.
pat splat — 7 weeks ago
Run premix ok
pat splat — 7 weeks ago
Moded hf set. A new set of clips lets you get the fit and movement just right especially when you mangel the ogs. Last time i went down this road was about a year ago n it wasnt too bad. 15mins max.
pat splat — 7 weeks ago
Usually you get the throttle cable going from the carb back to your grips. Little tiny part fits into carb(shape as needed). Then on your grips/controls you cut cleanly and add a knarp(appropriately) sized. It a barrel with a set screw that tightens with a small screwdriver. Bat out.
pat splat — 7 weeks ago
Lisle 10100. I think thats the number
pat splat — 8 weeks ago
Pipe thread is made not to leak, otherwise the world would blow up.
pat splat — 8 weeks ago
Damm getting up thereThe rear mag is missing a web. Fixable? Braze?
pat splat — 8 weeks ago
I think i got a beat up one in ohio that needs work, ill be there late summer so remind me then if you still lookin.
pat splat — 8 weeks ago
Is it ridgid?
pat splat — 8 weeks ago
So...i cant seem to piece this together. What you see is what u get for $50 picked up in garden grove. Motor has compression, magneto 6933 is buggered. Ill be around for a month so grab it now...
pat splat — 4 months ago
Lotsa times on a garelli or your girelli the stator side crank seal goes bad. Just take a couple large screwdrivers and pop the dizzy off.Wait... get the correct puller and do it right. Change the other side too while u at it. Use nd30 fluid.
pat splat — 4 months ago
Dirty connections aside, The sissy bar for the carb/intake is badass.
pat splat — 4 months ago
Hard part is figuring out why it gets stuck.I wish i had a big set of channel locks.
pat splat — 4 months ago
If it aint broke dint fix it. Just clean n lube it up.
pat splat — 4 months ago
So it can spin in reverse, very retro or actually very thoughfully engineered for future variable applications.
pat splat — 4 months ago
Just imagine having a working speedo. Lube everything up ith some oil, drive cable pulls out and speedo(take it out).
pat splat — 4 months ago
Turd in your main jet.
pat splat — 4 months ago
So... take a studied look at the diagram. A35/55 trannies r the same.Important, the spring has some resistance on that collar.It all just wiggles together, remember wiggle and peanut into slot...
pat splat — 4 months ago
Those r always bad. Take a read on myrons page. Although your points are waaay offset.To run brake lights w new coil you will needs some new brake switches and rewiring.
pat splat — 4 months ago
What kit? Look up leak down test.
pat splat — 4 months ago
knock down any high spots, you can test by orienting the piston and dropping into empty cylinder. Drop test. Also, Make sure the rings are gapped and move freely.
pat splat — 4 months ago
Thanks for rounding out the thread, so many just leave one hanging.
pat splat — 4 months ago
If it makes it doen to oc i can splooge weld it.
pat splat — 5 months ago
Theres a kit for lazy people. 10 n 12 included.
pat splat — 5 months ago
Your correct to atart with compression. Buy or borrow a proper compression tester. Tranny oil level is not gonna affect starting.
pat splat — 5 months ago
Fyi, totally unecessary to get motor spinning, just push start.