Results 181–210 of 6280
That's the manual and wiring diagram for the 2 wire CDI
NOT MY LISTING:http://denver.craigslist.org/mcy/5822965159.html?lang=es&cc=mx
I get my exhaust on Thursday. First thing I'll do is check timing to make sure I'm close to 18*.My plan on the wiring is to check resistance on each wire to ground, I think the higher resistance the more power the coil will produce.https://www.mopedarmy.com/forums/read.php?6,4042355A regulator/rectifier also came with the motor, but I have no idea what pins do what.
On my last build I did CR80 forks with a hydraulic disc brake setup. I'll probably do something similar.
Thanks guys. I picked up a big muff pipe from treats for now.When I go H2O I'll probably pick up this kit and a matching scooter pipe: http://www.racingplanetusa.com/cylinder-polini-evolution-minarelli-horizontal-engines-p-166157-1.html#.WBC7P3NlDqA
I think you're talking about this one but I don't think it applies.https://www.mopedarmy.com/forums/read.php?6,3911019,3911068#msg-3911068
This may be helpful for later...
I bought this for my derbi start 5 (v) motor, I figured out that the green is the ignition, I got spark. Anyone know what the other 3 wires are for? Headlight, running light, stop light?White/redWhite/yellowBlue
Thanks Ed, I'll check it out. I've seen some with holes cut and then metal screen inserts to keep big crap out.
Because I didn't have a swingarm and don't really like the way the derbi swingarm works. I'm also going to try and keep the original pedal shaft, but I'll have to extend the right side some.
Some people may disapprove of my methods but I want to share what all I did to mount this beast and my struggles.Mounting width at bottom of the frame measured to 65mm, but top ones are slightly narrower.Here's what 65mm looks like compared to the derbi width:Derbi case is about 90mm wide.Cut the top mounting holes off the frameCut the lower right boss off of the derbi motor. Keeping the lef
Look at this on eBay http://www.ebay.com/itm/272418745074
$130 shipped and I'll include an intake I made for a TM24.
How much for the silver tomos tank?
Torn down and I'm eyeing a new pipe...
Mine is off a kx65, it may be small for a 74cc kit.
Kick stand for Puch freespirit or Magnum.Includes mounting block and hardware.No cracked welds.$30 shipped.
Buy both for $35 shipped.This headlight: http://www.treatland.tv/honda-MB5-replacement-headlight-LAMP-p/honda-mb5-headlight-lens.htmNew, never used.$20 shippedThis petcock: http://www.treatland.tv/OMG-honda-motorcycle-petcock-14mm-x-1mm-p/omg-14mm-01z3264268.htmNew, never used.$20 shipped
Original genuine Athena 70cc reed kit, not the knockoff. Like this, but with reeds.Known as the little Gila, can easily get you to more than 50.Original reed block with metal reeds. I've never had a problem with these metal reeds.Original Athena piston, no rings.Cylinder is in great condition, no scoring or chips in the nikasil.Casting in the exhaust flange is kinda rough.Exhaust studs are b
Just pulled this off my freespirit to do a derbi motor swap. I rode it up and down the street at 8:00 this morning, ask my neighbors. It has about 100 miles on it since the build.ZA50Roller crankshaftNew bearings and sealsNew shift pucksFlipped second gear clutch, maybe a stiffer clutch spring (I forget) Shifts around 30. With a 70cc setup.Stiffer clutch spring on firstOil pump block off plateCas
What's it going on? Bike/cylinder?
Tig welded the decomp hole and channel then dremeled/sanded it back in to the rough shape. I grabbed a picture before I did the final sanding with sandpaper:Malossi carbino 4 petal reeds/block:Head and stator installed. I picked up a 4-wire start 5 CDI.Parmakit CDI box from treats:I figured out that the green is the ignition, I got spark. Anyone know what the other 3 wires are for? Headlight, run
Try changing the rod length and resubmit. Watch the numbers change.