Results 31–60 of 294
ATZ — 13 years ago
I'm thinking maybe Estoril or homoet 6p how much better is the 6p?
ATZ — 13 years ago
I'm looking for a pipe for my Yamaha Yg1. I havent had much success finding anything for 80cc motorcycles. I'm looking to just cut and weld onto the stock header. Anyone know of anywhere I can get a good one? If I cant find one I was thinking just snagging a moped one. What would be the best pipe to get? I want an all around increase in power but would like top end more than anything.Zie
ATZ — 13 years ago
suppose I want to put a pipe on this thing by cutting and rewelding one to the stock header pipe, what would be a good choice? Would a moped pipe work? It would need to be something big enough to fit the header to.
ATZ — 13 years ago
Hey anyone know how to tune the oil pumps on these things? Also how do you bleed the oil pump before you reinstall it?
ATZ — 13 years ago
Hey thanks for the info dudes. Mark your brothers bike is fricken Fresh!
ATZ — 13 years ago
around 45 ish I know the top speed for these is around 53. I tried a smaller sprocket but I lose to much power. Also 4th gear with stock gearing I lose alot of power. Any Ideas? Jetting?
ATZ — 13 years ago
so I have this YG1 and its a awesome bike I just wish it had more speed. I was just wondering if anyone has put a pipe on one or a bigger carb maybe? Its frustrating because it seems like the carb is kinda small but you cant just up the size of the intake like you can on other bikes. anyway whatever anyone has done just throw it out there. thanks
ATZ — 13 years ago
What do you dudes know about these? there isnt much out there. Anyone know where there are parts for these?thankshttp://www.skidooalpine.com/1968_alpine
ATZ — 13 years ago
its a 1968 Yamaha YL2 trail master
ATZ — 13 years ago
I'm new to wiring and kinda use to the simple moped hardwire business. ok so i have an 60's yamaha and it won't spark at all. I have done everything in my power to try and get it to. I replaced the points, I wired from the generator directly to the coil. the problem is I dont know if the coil is shot or not. It has a negative and a positive wire hook up. I used a voltage tester to s
ATZ — 13 years ago
ok so i want to swap my YG1's 80cc rotary engine with a 100cc rotary engine. the only issue i can see is that the 100cc runs a 12v circuit and the 80cc that im running now runs a 6 volt circuit. I want to keep the wiring on the yg1 because it's all hooked up and working well, but I don't have a battery at the moment. so my question is if i put this engine on that runs a 12v system w
atz — 13 years ago
so i started rebuilding. i took it all down and finally got to the gears and didnt find anything unusual everything was very clean and all the gears seemed fine. i couldnt really see any wear on them at all. so ive started to put it back together and ive hit a snag i cant figure out why every time i put the metal cover that goes over the rotary valve on the crank wont move its like the cover hits
atz — 13 years ago
i recently got one of these and i got it running but i ran into some problems. my first problem is the kick starter slips i can get it started but it slips most of the time. also the shifting seems to be screwed up when i shift i have to push the shift pedal down really slowly until it grabs and when im trying to shift up into second its like im stuck between gears the shift pedal will move and it
atz — 13 years ago
i just got a yamaha yg1 i was wondering what kind of oil it takes. what kind of oil is pumped in the cylinder on from the side of the bike and what kind of transmission fluid do these take?thanks
atz — 13 years ago
ok sweet thanks
atz — 13 years ago
anyone have a wiring diagram thats what i really need
atz — 13 years ago
hey anyone have one of these i just picked one up and started restoring it. i kinda want a manual anyone have one? maybe post it up as a PDF?thanks
ATZ — 12 years ago
I hit 40 on flats with a proma gp and 17 X 45 gearing with a high comp head and mild porting. Does well in the low end as well
ATZ — 13 years ago
Impact driver
ATZ — 13 years ago
yeah I was thinking bullet head light to hide the speedo too or maybe the bike speedo. The cleaner the better!
ATZ — 13 years ago
1 more
ATZ — 13 years ago
another
ATZ — 13 years ago
Here are some updated pics...
ATZ — 13 years ago
yeah the seat needs work i agree and definetly a pipe and kit
ATZ — 13 years ago
you should throw a round bing on there it will make your life easier in the jetting department
ATZ — 13 years ago
1 more...
ATZ — 13 years ago
another
ATZ — 13 years ago
another pic
ATZ — 13 years ago
I know you dudes have seen this before but here is mine. Its nowhere near done but this is what ive got so far.