Results 61–90 of 9343
62. Re: Play in Front Forks of the Puch Free Spirit
Forum: Repair
So, I wrote that guide as I work almost exclusively in puchs and the main takeaway I was trying to convey was the relation to which forks go with what fenders.Free spirits have two different forks and only the regular free spirt uses the combos it does.Free spirit deluxe uses the exact same fender and forks as a magnum 2Regular free spirit has a lower fender brace that is exactly like a maxi lower
63. Re: finally got damn Bing carb to stop leaking....
Forum: Repair
Yeah, it can be a pain. But basically you want to make fir sure the seat is clean, the needle straight, and the floatshouod be perfectly level when upside down
64. Re: Removing front fork
Forum: Repair
It will literally fall right off once you peel up the rubber ring. Thin tipped flat head is all you need
65. Re: Help getting brake shoes installed... wishbone spring
Forum: Repair
Jeez. I've always just wedged em on and off with a big flat head. Never crossed my mind you'd need a special tool
66. Re: Removing front fork
Forum: Repair
I have a set of picks with various angles I use for all kinds of stuff, and one of those will get your o ring out in a second. Or a really fine tipped flathead.
69. Re: Puch motors for sale
Forum: Buy + Sell
Za3. Have a cover for this one too. Trans parts are there.
72. Puch motors for sale
Forum: Buy + Sell
4 left. 3 stock za50s, one e50.The e50 looks to be bored for a gila. Was rebuilt at some point as it has newer case hardware and an aftermarket crank.The zas are all bone stockThese should all be considered "parts motors" because I have no idea their story, except one of the zas I put a new wrist pin bushing in and maybe pucks but I don't remember because it's been years.$100 e
73. Magnum X for grown ups
Forum: Buy + Sell
It was an absolute blast messing around with this thing but I have other obligations at the shop as well. $1400 OBO open to trades as wellPush start e5050cc kitHeavily modified garelli swingarmReconditioned 17" spokesBrand new 15mm SHA carb and intakeHeavily modified proma circuit performance exhaustTuned clutch with ESO springsMagneto powered lightsNew ignition13/48 gearing all newNew cables
74. Re: E50 engine numbers
Forum: General Discussion
They're all supposed to match. Engine, frame, plate.
75. Re: What is the rarest moped part you own or can think of ?
Forum: General Discussion
Somewhere buried in the shop I have a moby leovinci low pipe still in the quarter kick box
76. Re: WTB: OEM Puch Maxi Pedal Chain Tensioner
Forum: Buy + Sell
The buzzeti ones really are top quality. Better than stock, waaaay better than the cheaper ones. I've got a bucket full of stock ones if you really want one but I'm telling ya, the buzzetis are where its at
77. Re: I WANT YOUR BROKEN INTAKES, CARBURETORS & REED BLOXX
Forum: Buy + Sell
Well, treats and mlm to be specific. But what the hell do they know about moped parts. Its not like I would know anything about it being hands on with product development and a block away from where its all made. This county is a manufacturing Juggernaut. We have some of the best fabricators and 3d printers in the country here making your moped parts.I wasn't here to shit on your parade, I�
78. Re: Riders for film needed
Forum: General Discussion
> classic carl jepsen wrote:> -------------------------------------------------------> how much does it pay?LOL!
79. Re: I WANT YOUR BROKEN INTAKES, CARBURETORS & REED BLOXX
Forum: Buy + Sell
Because its been attempted many times, funded well, by well known manufacturers and the results are always the same. The intakes warp and the weight of the carb distort them. Pretty much everything materials wise was tried, even carbon fiber. The results are always the same. I suppose in the case of case inducted, extremely short intakes like av10 and pugs there's less chance of that but with
80. Re: I WANT YOUR BROKEN INTAKES, CARBURETORS & REED BLOXX
Forum: Buy + Sell
Most 3d printers are at temp at 180°Large motors like said fords are cooled to usually about the same temp, maybe a tad bit higher than that, 190, 195 sometimesCase inducted intakes rarely reach much of a high temp at allPiston port cylinders often reach temps twice what a 3d printer wouldYes, I know technology advances and some newer plastics/resins can handle the higher temps, but heat it plasti
81. Re: Engine running without plug wire
Forum: Off Topic
Not acting crazy. Listen to what people are telling you. Timing and heat. Dieseling. Its not the bike, its you.
82. Re: I WANT YOUR BROKEN INTAKES, CARBURETORS & REED BLOXX
Forum: Buy + Sell
Plastic bolted to hot cylinders, what could go wrong?You'd think the bean counters at every motor manufacturer ever in all of time would have realized that plastic is far cheaper to produce than metal but hey, blaze those limp spaghetti noodles. I'm sure you know something none of them ever did.
83. Re: The infamous $2000 Maxi was STOLEN
Forum: General Discussion
You know, the way you describe all this, its almost like you're proud that a bike you built was stolen, like it somehow vindicates you.Nobody gives a shit about your beefs. Just give the important information. Pics, where and when it was stolen, who to contact if its seen.God, only you could make someone else's stolen bike about you. Ugh.
84. Re: Magnum X mods
Forum: Performance
Which speedo is more common, and why are there two different ones?
85. Re: E50
Forum: Buy + Sell
> Moped Lar wrote:> -------------------------------------------------------> > Avery M. wrote:>> > ------------------------------------------------------->> > Puch e50 engine. Turns over, top end is off it. Cylinder has broken>> > exuast studs but there is enough there to remove them.>> >>> > $195>> Then why not just remove the exhaust
86. Re: Have you ever wondered how much money you've spent on mopeds?
Forum: General Discussion
I'm just shy of $20,000 in parts from treats in the last 4 months alone soooooo.... Probably not best to tally this up over 3 decades.
87. Re: Magnum X mods
Forum: Performance
This leleu puch rim now fits this garelli swingarm like it was made for it. I still think I'm gonna shave a mm off the outer spacer of the bake plate but it looks damn good now and the centering is perfect. The rear tabs were cut and weld reinforced for maximum beefiness. Should line the swingarm up like magic. With this, I can now throw some 5ers on the mag x and throw these 17 x 2.75 Sava m
90. Re: I'm trying to fine a za50 first gear. 70 tooth
Forum: Buy + Sell
> paul liedtka wrote:> -------------------------------------------------------> turn your fuel filter aroundHAHA!