Results 61–90 of 174
38??? How what did you do to it? Go down a hill?
I am putting my puch back together. And I am running into a couple of problems along the way. For the side covers, there are 2 short and 1 long for each side if I am correct. So where does the long one go? In the front middle or back hole? Also I can see that installing this starter cable is going to be a hassle. Its a 1 spd motor, but any tips about the starter cable will be helpful. The wiring I
I have one and I like it. But the only thing I would change on mine I know some came with them but the 1984's didnt the kickstart.. I think they top out at 32, Mine has over 2000 miles and still runs just fine... and I remember i saw one on ebay with 8,000. Personally I think they are kinda hard to work on though. I got mine for free
I have gotten 2 free mopeds... A honda Spree and a puch newport. Are those peugeots the same exact ones???
Drain the old trans fluid out... Put fresh in, it sounds like its trans fluid leaking but its probably from 1977 so it could be black. But if it isnt that leaking I am not sure what it is. To empty the fluid there should be a plug somewhere under the motor on the left side (if your sitting on it) drain it all out. Then I am not sure but someone else will know how much to fill it with. You take out
I think its the gutner carb or however you spell it... my freinds 103 does the same thing when he saves enough hes going to replace it
so tabpat did you have a title for it... because i have no title for mine and i know its going to be a brew ha trying to get it road legal
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&category=6737&item=2419563174is says the top speed is 50mph??!?!but it looks like its going to go for alot because its still got 8 days i think and its already got 5 bids
what do you want it for if you dont even know what it is?
it resembles a spree to except for the bent upward exhaust
it says there are 16 replies to this post?!?!??
Okay I am getting my motor rebuilt and I was wondering if anyone knows where the O rings go for the eurocylinder??? Any help would he appreciated!thanks alotandrew mason
I had a moped dream last night too, I was actually riding my puch!... Then I woke up :(
talk about your good luck huh?
NO! you arent supposted to fill it to the top 9.5 oz!
ok judging by your info you have a 2 spd. There should be a hex head sticking out of the bottom... unscrew that but have a cup or anything to drain the fluid in. Then after its done draining, PUT THE PLUG BACK IN then take the rubber piece (probably tan color) out of the top on the same side of the motor near the mess of wires. I believe for the 2 spd its 9.5 oz. The spark plug take your old one t
Ok, first off let me give you the comfort by telling you I havent had any luck with tires/tubes since i got my puch. I believe I have had 3-4 flats ALL in the back tire as well, as for installing and taking off the old tire. The manual says use a spoon, and I use dish soap all around the outside of the tire that helps alot. The stickers..... auto zone or napa there should be a spray can called sti
i saw that bike back in september... it was clean and almost shiny, man what i winter can do to a moped! but i think it would clean up kinda easy
how long did that all take to do? sounds like an entire day of work!... Do you keep all your mopeds running and ride them once in a while or have they been sittin since they were restored?
hey when is it comming out?? I am not really into spiderman but i would go and see it...
the 50 mph tomos was so fast it escaped the picture frame!... (the pic doesnt work) :(
cool... how fast are you going when you do it?
If you are going by your speedometer its probably wrong..... I know mine is very far off
One of my friends is putting back together my motor after installing a speed crank, I have the 70cc eurocylinder. I want to know if the base and head gaskets are different then 50cc and if they are where can I get the right gaskets from?thanks alot
Fresh gas... New plug? is the motor warming up? timing? start with the less costly and easier things to check first
My sachs used to do the 0-25 in 13 seconds haha
I got a tire tube and the valve stem is on the outside of the tube... So that I would have to twist the tube in order to fit it in? Is this right... Last time i tried this the tube lasted 1 ride.help?
Nah its not spray paint.. A 200 dollar paint gun with 70 dollar paint. And yes i did sandblast it :)