Results 1–24 of 24
Rasmus Langberg — 3 years ago
i shit you not the wedge that locks the flywheell was split in half. The wedge was only a few weeks old and i do not know how that could happen.
Rasmus Langberg — 3 years ago
my maxi is runiing way to hot in 68 degrees weathersetup 70cc airsal15mm bing 76 jetgearing 14:40sparkplug ngk b6hstiming's a 12 degreesi live in denmark , and the weather above is fahrenheitit ran so hot that the 28mm stofck pipe got hot all the way up to there you mount it at the rear wheel.the story goes that in denmark mopeds are to be ridden for 15 year old therefore you can only go 20 m
Rasmus Langberg — 3 years ago
In denmark they are called a "knallert" "knall" meaning a loud noise and -rt is a plural. so the word mean "many loud noises"
Rasmus Langberg — 3 years ago
Sure thing wasn't being a smartass, just curious. They aren't called mopeds in europe i just know the english term for them not the whole meaning behind the word.
Rasmus Langberg — 3 years ago
Hey mopedarmy. I live in Denmark where most of our mopeds comes with a kickstarter instead of pedals. moped like puch maxi, kreidler, sachs, yamaha all comes with footrests and a kickstart. why is it that all the mopeds in usa i've seen on youtube have pedals? is it enforced by law or is it just that not many kickstarter models were imported?
Rasmus Langberg — 3 years ago
i should run a filter but i don't. i have one ready and never used but havent got around to cut the fuel line and put it in between
Rasmus Langberg — 3 years ago
looked like a cut tobacco leaf from a standard cigarette
Rasmus Langberg — 3 years ago
The answer was found. in the carb at the fuelhose connection there were a tobacco thin leaf that when the vacuum from the engine went high enough closed itself off. removed it. works all good now.Thanks for all the help!
Rasmus Langberg — 3 years ago
no fourstroking
Rasmus Langberg — 3 years ago
it's a copy of a 15mm bing. here in denmark puch's and other mopeds come only with 12mm bing and are restricted to 18 mph. moped in Denmark can be was ridden by 15-year-olds and therefore they are restricted. so the bike didn't come with a original 15mmm bing.but what is the difference from the real one and the copy?
Rasmus Langberg — 3 years ago
if I should guess I'm leaning towards the small mesh in the carb. thanks for the tip I will try that.
Rasmus Langberg — 3 years ago
the flow in from the peacock is pretty good. its a steady full stream. how would I adjust the bowl to allow more fuel in it?.a note to ad to the hole thing. before i had a 72 jet ind it . with the needle at 2. from the top. and it didn't do that at max speed. should i try to move the needle up to 2. from top or?
Rasmus Langberg — 3 years ago
Hey, my 70cc maxi is running a bit strange. it runs like a dream when all the from the takeoff to top speed but there is an issue where if I drive full throttle for 3-4 min the engine starts to bog down and if i let the throttle go a bit back it picks right up again. it drives 65kmh (40mph) with a 14-36 gearing. to a reading a about 240 F when driving I could be a bit higher. Some more informatio
Rasmus Langberg — 3 years ago
this is a really good way of cleaning your tank. it's not English but subtitles and watching will be more than enough information
Rasmus Langberg — 3 years ago
it the timing. The screws got loose and the timing had gone full advance. No damage is done so I guess I was lucky. The clutch also need 1 turn in on each side
Rasmus Langberg — 3 years ago
Hey, I have a problem with my moped that if I give it full throttle at low rev it makes the bwraaa dying sound but if I get it up in mid/high - high rev then it drives like a dream flat out (40-50 mph) acceleration is also down in the start. no four stoking at top speed. I had a 64 jet in and then the problem were I could only drive with 1/3 throttle but would die at full.Setup70cc airsal kit28mm
Rasmus Langberg — 3 years ago
i'm using the same of on my friends stock bike. Can't it at least work on that?is this a better crank to use?https://www.jmpbdele.dk/krukas-maxi-top-racing.html
Rasmus Langberg — 3 years ago
I'm putting a performance crank in next week. but i'll try a bigger jetThanksCrankshaft:https://www.jmpbdele.dk/puch/engine-parts/crankshafts/krukas-maxi-race-dmp.html
Rasmus Langberg — 3 years ago
Hey mopedarmythe problem I'm having is when the engine is cold I can drive full throttle but after 10 mins for so of the engine warming up then the moped start dying if you give more than 2/3 of the throttle. I know it the main jet but so I go up or down?setup:crankshaft standard70cc airsal kit28mm pipe the bigger one that still looks like a normal pipe15mm bing - 64 nozzlespark plug NC10HS R
Rasmus Langberg — 4 years ago
its about 16 before top
Rasmus Langberg — 4 years ago
hey mopedarmy!í have a problem surrounding my puch maxi with 70cc airsal kit on. it can't run and dive, but same speed as a 50cc and the exhaust turns candy apple red at the beginning of the exhaust where you mount it to the cylinder.My setup is:-70cc airsal cylinder-70cc head-28mm techno pipe ( the standard but bigger )-15mm bing jettet-15 intake-standard clutch- standard crank- gearing 13:4
Rasmus Langberg — 4 years ago
Hey i am installing a big bore 70cc airsal kit, but i don't know why it wont go on. the cylinder should fit and the piston can in the top move back and furth. But when the piston hits the bottom of its stroke it get stuck and can't move back up. What so i do?
Rasmus Langberg — 4 years ago
It was the timing that was off Thanks!
Rasmus Langberg — 4 years ago
Hey! i'm fixing my friends maxi, but there is a really wierd problem where the engine have spark, set timing, and fuel, but after you hit the kickstarter the engine won't continue to keep firing. only when you hit the kickstarter you can hear a single bang from the engine but not any more than that .