Results 1–22 of 22
YO, Crazy Wings?! That place is the shit. Im from that neighborhood. Lemme know next time yall are out!
Yo, y'all are rippin it in Lincoln? Hit me up! Putting together a maxi.
for real, thanks for this
Just for clarification can someone try and explain the feeling of slippage and engagement?My understanding here is that Engagement is when it hits and your bike starts to take you flying like that son of a bitch you're trying to be, but im a little unclear on what slippage feels like....right now my bike picks up right away really well, but it seems to rev to low mid-ish range and then drop r
Hey all, im running a 77 maxi, 14mm carb, proma circuit, and blue clutch springs.runs great at mid, with decent max speed down hill but take off is pretty slow... any tips on how to improve that?
runnning stock 77 maxi with a proma circuit. Wheres my powerband? how should i tune my clutch to receive best power and max torque? currently have blue springs in flush, seems to be best at mid ranges but doesnt hit very high speeds or accelerate from stop very well.
How is timing set with one? Especially if it's variable?
Is a CDI worth getting on my 77 maxi?
90% sure its the exhaust. Its pretty oily down there...
Im having a similar issue. I just did an engine rebuild. New seals, crank, bearing amd condenser. Ran perfectly stock, upgraded to proma circuit and found out my jetting. Running sweet but couldnt idle. Found an airleak and literally right after i cant get it to start at all unless i wait for it to cool or something.Edit: air leak didnt exsist when it ran stock. This seems very strange to me
tapped it, flushed it. easy does it new bolt screws in like a charm, thanks all
Why would I purposefully want to retard or advance my ignition timing?
i set the needle to the top most notch, using the 71 jet it rides pretty good, low end sucks a little but is alright. doesnt want to idle and 4 strokes going downhill when trying to reach higher speeds.rides totally fine uphill and on flat groundedit: i have blue clutch springs in turned about 3/4 a full turn past flush. this wont have anything to do with my fuel/air mixture though right?if i let
71 jet (i dont have a 70 or 72 but i can just order some) works well, but it wont idle and i think it's 4-stroking? im not exactly sure what 4-stroking feels like. ill have WOT and be cruising fine. when i roll off throttle and then engage again it runs supper rough and feels like its skipping.Edit: seems to get worse with a 69, still cant idle.also, havent cut a hole in the slide yet as i do
high flow from treats14mm2.22timing is set at 15 degrees with a .016" gap. might be a little off though cause i used the cereal box/screwdriver method.as far as needle setting im 98% sure its on the second notch from the top
seems like its the case threads, bolt looks fine
did some clutch tuning only to find out that the transmission fluid drain bolt has stripped away at the threading in the drain hole. slow leak, only to find a small puddle underneath this morning.i cant just go and find another bolt can it?any thoughts?
Hey guys,just threw a proma circuit on my 77 maxi sport. upjetted from 66 (which i think was running rich) to a 73. started up no problems, idled fine for about 2 mins and then died. took a while to start up again but now it just dies almost right away.this is my first moped, just did an engine rebuild and have been riding it stock for a few weeks.did i upjet wayy too high at first? i know i need
Hey guys, new here and doing my first rebuild. I want to clean out my puch maxi stock exhaust pipe, reading the wiki it gives my two options, heat treatment in a fire for a painted exhaust, and chemical treatment (which has little documentation, advice.) as youre all well aware, the stock pipe is shiny, so im assuming it's chromed. Would i not want to stick that in a fire? and why not? also,
Hey guys! new here, i have a 77 maxi sport, runs like shit. decided to do a rebuild so i can learn about the engine and get it running clean and smooth. any advice? tips? tricks? i know a little bit, and have watched some videos and things but if anyone has some great starting tools/resources i would greatly appreciate it. Thanks!