Results 1–30 of 41
Mel FromDCL — 4 years ago
Lookin for a good puch 5-star rear hub if anyone has one.Thanks
Mel FromDCL — 4 years ago
So.... this is what we ended up doing...Just wanted to report back with an update.We ended up using these puch shoes with modification listed below.https://www.treatland.tv/productdetails_popup.asp?productcode=groovy-pads-13957-80x18-yWe ground about 1/16" off of the top of the pin end with a cutting wheel - and about 0.5mm from the end that goes against the pin.We used the springs that came
Mel FromDCL — 4 years ago
ohhhhhh. I like this idea.. thanks.. the springs an everything are still good on them! thanks :)
Mel FromDCL — 4 years ago
Yes.. changed it to one with the roller bearings from treats.. I had to.. the other one was broke.. the connecting rod looks llike a "S"
Mel FromDCL — 4 years ago
I blew up my kstar kit (that came on the bike when I bought it) when I hit around 416 this summer.. but I also had a massive air leak unbeknownst to me at the time... hence the total rebuild.. so I am a little skittish about temps at this point.
Mel FromDCL — 4 years ago
We just redid my '77 with very a very similar setup.70cc Treats party with the "custom cut sport/touring" head. 15mm bing (with MLM intake and air filter).techno circuit (not proma circuit) pipe - so close.Our timing is at around 14.5-15ish. 14-45 gears (stock). We get 38 mph out of it on the flat, max.. We have an 85 jet in it... it does 4-stroke a little at the top end- I have
Mel FromDCL — 4 years ago
We could make them work if we ground the end on the one side. It wouldnt be just a drop in.
Mel FromDCL — 4 years ago
That looks right and I remeasured. yes 80x20....that is where I should order it from? no one domestically sells them I assume?I see treats sells 80x20 but who knows if they will fit? doesnt mention motobecanes, says suzukis.
Mel FromDCL — 4 years ago
Motobecane.. I am guessing original since the bike had everything original when I bought it (odometer reads 324 miles)looks like 65x20?I attached comparison of the old ones and the 18x80 (puch) shoes we have on hand... I dont mind ordering the exact ones.. just cant figure out what to order.. and hoping to have the bike ready for next weekend.thanks
Mel FromDCL — 4 years ago
I have an old 50v witb 6 star mag wheels. the rear brake pads fell apart.I cant find on treats what to buy..everything they have says it is for spoke wheels.I have 18x80 new pads on hand (I have a maxi also).can I buy the appropriate pads.. or we see that we may be able to possibly modify the 18x80s to work.. is this what some people do and is it successfull? any writeups?thanks so much for the
Mel FromDCL — 4 years ago
I have a biturbo pipe from a e50 (maxi) - was only used maybe 100 miles.$25Chrome techno boss for flat port puch - still new in bag - $35
Mel FromDCL — 4 years ago
yea... uh... what had happened was...This is on a '77 newport that I had bought a few years ago that the p.o. had put a k-star kit on. When I got it, it was really low miles. I had upgraded to a 15mm real bing and mlm intake fancy mlm air filter.. had made a little window in the side covers for the air filter. I also put a circuit pipe on it since we have hills here in Pittsburgh.It was r
Mel FromDCL — 4 years ago
we have it apart.. thought I would post a better pic of the crank...
Mel FromDCL — 4 years ago
thanks for the insights!yea it was a pretty gnarly scene when we took it apart.. little pieces everywhere. We are still newish to mopeds... so learning the hard way while we go I suppose.
Mel FromDCL — 4 years ago
My E50 on my newport blew up on the LGN rally... I have a new cylinder, head, piston, crank for it... but I am a little concerned if the bottom end is still useable... the conecting rod clanged into it obviously.... can we smooth it up and use it.. or is it toast?im specifically referring to the gouge on upper sidethanks
Mel FromDCL — 4 years ago
ahhh... it's okay, I will just get something when the time comes... got a lot to fix first.
Mel FromDCL — 4 years ago
Monti... I might be interested in it... we have a Sachs Balboa also that I bought a kit for last week (under Franks advise). Not that I will be getting to it anytime soon, after the snap crackle pop on my Newport, but would be good to have for when we get 'round to it. I can paypal ya some dinero and we can meet up sometime at some point.
Mel FromDCL — 4 years ago
pm sent
Mel FromDCL — 4 years ago
wow.. that is nice! specs? what all did you do?> Jared Rut Wrote:> -------------------------------------------------------> I'm rebuilding a magnum for my wife. Odds and ends left to do and the> first start quickly approaching. Starting to get excited!
Mel FromDCL — 4 years ago
I commend your sense of adventure, and I totally think you should do the trip... but I am hoping that your mom may be able to give you and your bikess a ride for sketchy sections....That area through WV - basically Clarksburg and east has some really really steep and winding hills with logging and fracking trucks running up and down them....Here is an example of one 9% grade hill, and there are se
Mel FromDCL — 4 years ago
> DJLou Magnetos ($M$) Wrote:> -------------------------------------------------------> The take away is you should have a matching pair of gazelle tires, and> clean gas tanks or your moped may catch on fire.definetly 10 miles down the road.....
Mel FromDCL — 4 years ago
I am mostly a lurker.. but had to say..this bonus episode this week was great. Charlie Buzzard was a great storyteller.. though I still dunno what concert the guy was gonna see in Jacksonville... either way.. it was really entertaining.
Mel FromDCL — 4 years ago
def interested.. lemme know how much.Im driving to detroit for the next 5 hours will check back after i get there if u send me a pm. thanks
Mel FromDCL — 4 years ago
Lookin' for:Puch mags/snowflakes wheels pairMKII hydraulic front forkskill/run switch for a maxi/newport in nice shapeI will be there sat evening.
Mel FromDCL — 5 years ago
You are welcome :)> Les Briones Wrote:> -------------------------------------------------------> Thanks to Mel & her Pops. Just built my work bench with help from my> little grandson! He loves mopeds... I just leave the Vespa up on> it.Looks good
Mel FromDCL — 5 years ago
yep. that is why they are there... and there are 2 on the other end also.
Mel FromDCL — 5 years ago
here is an other picture I took.. it shows the center support.. which I think was a good idea.Oh and it is also a nice height to sit and drink beer on!
Mel FromDCL — 5 years ago
Lol... that is my husband, I built that stand with my dad.I have to give props to the Zeros - who had posted some live update videos of their shop in preparation for their rally a few weeks ago (which I wasn't able to attend)... anyhoo - I saw them working on something like this in one of their videos, so I talked to my 73 year old Dad, who likes building shit like this for us - and we did th
Mel FromDCL — 5 years ago
hubby
Mel FromDCL — 5 years ago
Kodi Bear has seen some stuff in the shop lol