Results 1–30 of 458
my tank sucks, anyone have one? has the red stripes
anyone have any performance vespa pipes laying around?want to try a different pipe, for a grande.pm me
bump, still looking for this :(
hi looking for either a complete wheel or just a rim for a derbi.tried a non derbi rim and it did not work with the hubs/spokes
word! hold it for me til i see you next ?
looking for -variant brake plates (2)piston port flywheel side coverpp variator side covervariant center plastic coverseat
does anyone in ohio have a 17" spoke rim? dont need spokes or a hub, just the rim.
3-- in the above photo, the right side shaft has a large double needle bearing that fits inside the mini output shaft. that same bearing will fit on the left side shaft, without it the left side gears dont fit on the shaft properly. is it safe to assume there are two of these and im missing the other?4-- last question....what the fuck is this arm mechanism? whats its function and does it attach to
working on reviving another pile. engine was partially apart and had half of the internals taken out before i got it. most of the internals were sprawled in a box, im not sure what im missing, as usual.cases say "derbi rabasa coaxial"i found a shop manual online but it seems like the engine internals they have shown are different than the one i have. the pics here show two internal chain
hey is it only one side fairing or do you have both?
found most of what i needed,does anyone have a used derbi piston port expansion chamber exhaust laying around?
looking for parts for a variant tt project:seatfront and rear brake platesfork tubespm me
i have one i believe. got a picture of yours so i can make sure its right?
hm ok this does look like fun, let me ponder it.al u got any pics? might be interested
need a new project looking for a v1 roller. mostly complete (frame, wheels, seat, bars, kickstand)just need some good bones.step thru or top tank idc.alsoif you have a mostly- complete parts bike (of any make or model)or even a good ol non running sitter,hmu with what you have i may be interested in it depending on whats still on the bike.
ive got a str8 shooter, sealed off oil port. 25 shipped pm me if u still need one
all four intakes gone30 shipped for the clone30 shipped for honda carb60 shipped for cable choke 19mm phbgpm me
for sale::all prices un-shipped, i will combine ship items if you want to bundle--two slightly different 19mm (spigot mount) intakes for use with tomos reed cylinders and phbg carbs. 25$--side shot angle intake for 21mm carbs and tomos reedblocks. 25$--puch polini intake for dellorto sha i believe. 14$--legit dellorto 19mm complete carb with the good atomizer. 70$--knock off phbg 19mm almost compl
yo i have a carb. its got the good #40 slide and w7 needle. idle and main jets are probably in the ballpark already if ur running a kit. also have a small velocity stack on it. pm me with an offer if interested
either one is fine but i prefer mount grounded, less wires. u got one nick?
looking to snag a working used one (not aftermarket) locally in ohio, unless you got me for 20 shipped.
makes sense thanks for the tip, mine didnt blow luckily.
ok got it sparking with the external coil from my main tomos.thanks guys. i was using a new coil off ebay but here's my hypothesis and what happened...rebuilt the engine as usual.tested it for spark, makes loud electrical pop get bright spark then nothing.i take look at the stator, the coil is scratched and shorted and i didnt notice before.get new internal coil installed, test everything, no
trying to get a tomos a3 parts engine going for a build. ignition is running me in circles. i had it sparking at one point then i lost it again. now it makes voltage but its took weak to jump the gap, shocks you but no spark.last time i had this problem on a different renovation, it ended up being a slightly corroded points wire connection (tiny nuts on the points) in the stator.2-wire idm labele
i have a cdi stator id sell for cheap pm me if u need it.
bump looks like i just need a tomos a3/a35 ignition coil. mounting holes are approx 2" apart.
yeah it sits stupid low when im on it. thanks guys il try 270 1200lbs