Results 1–27 of 27
This is where I’m kinda lost, with it being a 50cc still but now a reed valve motor should I be looking at big jets to start? Stock jet on this was like a 52 or something with sha carb but now with a race cylinder reed valve and 19phbg, I’m just looking for a safe starting place. Currently have a 94 but so afraid to seize it again since this kit is impossible to find!
Well I I’m pretty sure my ignition timing was spot on being only one point, but I bought a cdi I the theory something is off with my ignition timing. I know it’s with the carb! I just don’t know where to start! Right now it’s fouling super rich(wet plug) trying to start and have it idle so I’m thinking I had fuel flow problem and now my jet is waaayyyyyyy too high. But the bars are kids Schwann bi
Hey guys I just pulled the ped out of the basement after a couple of years, it’s a Benelli G2. I have the Malossi 50cc reed valve kit, MLM peoples pipe, Puch 3 shoe clutch, 19mm PHBG and I’m waiting on the mini rotor cdi to come in. Long story short she seized once, still good though! Anyone have experience on setting a base tune for engine that is now a reed valve that wasn’t before? Setting a ba
Bring this back from the dead! I have a G2 and I replaced the stock clutch with a 3 shoe and used the original bell, plate and spring (it's mangled but I made it work, long not really story.) I found clutch material in my side cover when I went to change out the springs with some nice blue performance ones, I'm also running the malossi 50 reed kit with a 21mm phbg some my rpms are redux!
Yes, engine was recently rebuilt! The w6 needle on the leanest gurgles slightly at half throttle, 94 main I think possibly a 93? I tried a 96 and ran like crap! My temp gun measured the head around 330, cylinder around 300 and pipe at 400. Is this tooooooo hot?
Howdy y'all! Sooooo here's the deal, I have the malossi 50 reed kit on my G2 with a 21mm carb and can't tune the damn thing! It seems to be always rich with a 96 main, w16 needle cause the w7 bogs it out and I'm waiting to put a w6 in it. Atomizer is now au260 with a idle of 40 which now seems to be spot on (thank god) but it's always hot and always rich! Full throttle fee
Okay so I have basically no lights at idle, is it safe to replace the lighting coil with a 12v to actually have lights? I'm looking to upgrade!
Hi all! Are there any reviews out there on the malossi 5pcc reed valve kit fpr the benelli g2? Thanks
Hey it's a dead post but I bought the altered kit and it is totally wrong! Complete no go for any future attempts.
Hey y'all, ISO a cylinder kit for l a Benelli G2 and head gasket!
I did actually bump up my idle but it didnt help...im just gonna rewire this whole bike
Performance is great, its just that the lights are either super dim or not lighting until the rpms pick up. Once moving theyre bright but im worried about turtling up a hill and not being seen.
Thanks a bunch for the advice, but how exactly do i set them? Where am i measuring the index card gap?
Ill check my center stand and all grounds, can you guys point me in a good direction for bulbs!? I have a 6v's but id like maybe an led bulb?
Hey all! I have a moto guzzi robin/benelli g2 rat creature, my problem is the lights arent "on" at idle. With the kick stand down and the rear tire spinning i have a faint headlight, not much of a tail light. While its running however they are bright, but going up a hill or sitting at an intersection at night has me a bit spooked with not being seen. Anyone be able to point me a good dir
Hey guys, im wondering whats the largest carb i could possibly run on my stock cylinder G2? I have a 12:9 now and its not pulling its weight enough, need a little more speed! Thanks
I can fabricate, not a huge issue for me. Ill try searching around those models. Thanks!
Hey guys! I heard there is a Benelli 65cc 3 speed engine out there! Is this true!? Would be nice to have since i have a bunch 45+ roads around me. Please let me know guys! Thanks
1977mopeds does not have polini kits left! Im am curently being refunded...
Thanks for the imput! I emailed treats asking if it still bolts up fine, waiting for an answer
Hey chad i sent you a pm,
Yeah man i my phone glitched so i made a second incase. Thanks a bunch about 1977 mopeds. They had a kit! It was a little pricey but i havent seen one up for a long time
In search of a benelli g2 cylinder kit or another kit works for it?! Please help!
In search of a kit for my benelli G2...also known as the moto guzzi robin same motor. Or if anyone knows a kit that will bolt up!? Thanks much, Ed
What oil goes in the 10mm bolt on top of the engine??? I can't find this out!
I've got a question. I rebuild my g2 and noticed. A 10mm fill bolt on top of the engine, does trans fluid go in there and if so much?! I filled the case at the big bolt on the side until it started Slowing coming back out...am I doing this right? Can't find anything in this...