Results 1–30 of 65
Moped Man — 5 years ago
Can we get some more details?
Moped Man — 6 years ago
Are fire pits acceptable?
Moped Man — 6 years ago
Its gonna be sick!!!!!!!More info!!!
Moped Man — 6 years ago
Just tried the 14mm and it did not run differently. Any other input?
Moped Man — 6 years ago
Ken Roff Wrote:-------------------------------------------------------> Get/run a real 14mm BingI will try to do so as soon as possible. What range of jets would you recommend?
Moped Man — 6 years ago
Ken,I should have been more clear. I was showing the base of the engine because yesterday I posted "I will go ahead and check squish in my auto shop class tomorrow. I will also check compression and take pictures of my case match, and cylinder/piston."According to Fred's guide, "Metal head gaskets can be reused over and over as long as you didn't damage them by bending the
Moped Man — 6 years ago
I checked my squish, and in the process I realized that I had two head gaskets instead of just one. So after removing one head gasket, my compression went from 150 up to 160 psi. My squish came out to be 2.565mm. I didn't want to remove my cylinder all the way, because I did not have enough time. So here are the best pictures I could get.
Moped Man — 6 years ago
Steve Miller-I will go ahead and check squish in my auto shop class tomorrow. I will also check compression and take pictures of my case match, and cylinder/piston.
Moped Man — 6 years ago
Ken Roff Wrote:-------------------------------------------------------> Never advance it, lower it to specs> A bored out carburetor many times gives poor> results it's best to use a real 14mm Bing> carburetorI am very confident with the job I did with my carb, but I can borrow my friends bing 14mm to see if it is the root of the problem. I will clean my points, re gap it to .018,
Moped Man — 6 years ago
Ethan Brady Wrote:-------------------------------------------------------> Add an 82 jetAn 82 sounds really high, Ken roff suggested 71-73 and travis tutorial runs a 68 for this type of setup. But if you are confident in this I will give it a go. Do people usually upjet after advancing timing?
Moped Man — 6 years ago
If I can afford a vapor, then I will grab one. I can probably afford one later this month for my birthday. I notice that on flat conditions I hit 39 or 40, but if I blast down a hill, I can get to about 43mph and hold the speed on flats. When I hold a higher speed after a hill it sounds like I am 4 stroking. I am at sea level by the way.Here is a link to a playlist of videos of it running.https://
Moped Man — 6 years ago
I have double checked, and my rear sprocket is a 45t. That makes my ratio 17:45.
Moped Man — 6 years ago
Thanks Ken I appreciate the info. Ill pick up a trail tech as soon as I can afford it. I really don't think I have soft seized since it has been this slow from the start. The last time I took off the cylinder, I inspected everything and I did not see any deformities. Are signs of soft seizing visible to the eye? How would you recommend move forward?Thanks
Moped Man — 6 years ago
In order to get the feel for how it will engage, you need to ride around on it. Try to ride it around like you would usually do. If you notice that the tighter clutch springs are taking to long to engage, you want to back off on the adjustment bolt. Remember to always adjust in equal increments. The longer it takes for the clutch to fully engage, the faster you will wear down your clutch shoes. Fi
Moped Man — 6 years ago
I know I am running a 17 in the front. I assume rear is stock, but I will double check to make sure the previous owner didn't change it.As for jetting, I was running a 73 and I noticed it was running very rich, so I took off the air filter and it ran slightly better. After that I put a 71 in and reattached the air filter. I ended up having best luck with the 70 jet. This was before I decided
Moped Man — 6 years ago
Mike Boyd Wrote:-------------------------------------------------------> What jet is your friend running on his 50cc?He is running a 68.
Moped Man — 6 years ago
Hello everybody.I have done all the research I could using the wonderful search function, but I am still stumped as to why my Puch Maxi E50 Is not accelerating and hitting a higher top speed.My setup goes as following:-1978 Puch Maxi E50-treats 70cc piston port kit-treats hi-hi head-12mm bing bored to 14.3mm-14mm intake-High flow metal mesh filter-2.22 atomizer and 70 jet- mild case match (didn�
Moped Man — 6 years ago
Im looking for either a full a35 bottom end, or individual gears if you have them. Im located in CT. Let me know, Thanks.
Moped Man — 6 years ago
Savage
Moped Man — 6 years ago
Zack Synacri Wrote:-------------------------------------------------------> Brandon Love Wrote:> --------------------------------------------------> -----> > You paid $400 for a non runner?> > The fuck is wrong with you?> lmao> when you want a kitted out bike ,and have cash to> throw away..GO FOR ITActually I already have a kitted puch maxi. Case matched, 12mm bing dr
Moped Man — 6 years ago
For everyone asking here is the guys information so you can blacklist him and whatnot.TylerPoint Pleasant NJ(732)-778-1891
Moped Man — 6 years ago
moped man Wrote:-------------------------------------------------------> hey rourke... at the top of the screen, does it> say "flat view" or "threaded view">> if it says flat view, click on itWow this is life changing. Thanks
Moped Man — 6 years ago
Thats awesome advice. Thank you.
Moped Man — 6 years ago
The auto shop course is at my high school. Its a nice class to take because I get credit needed for graduating, while working on my moped. Im in my senior year.
Moped Man — 6 years ago
Haha there is no doubt that I will have fun rebuilding it. Thanks for the input.
Moped Man — 6 years ago
It does have a title, but I have not registered it yet.
Moped Man — 6 years ago
Pm sent.Thanks
Moped Man — 6 years ago
Im not from New Jersey, I'm from Ct... The purpose of posting this was not just to gripe, but also to warn others about the lesson I unfortunately learned the hard way. I am also not getting "spanked", because I already stated in my original post, that I learned my lesson about buying project mopeds. That being said, I still got lied to about the kit, which the reason why I said I g
Moped Man — 6 years ago
Warning: Long angry rant post.I saw a Tomos targa lx up on craigslist in NJ for 400. It had a brand new 70cc airsal kit, biturbo, and had a black paint job, but it WASNT RUNNING. I decided that this would be the perfect contestant for a summer project. I went ahead and drove to New Jersey which should have been a 2 hour drive away, but ended up being 4 hours. I finally got there and learned that t
Moped Man — 7 years ago
I have a channel for photography from my tbs discovery quadcopter. https://www.youtube.com/channel/UCXnyfrBhKrYylx-KNjBFJIw