Results 1–30 of 85
I think thet are a cool little bike. I have a nice one that I need to get the charging system working on. It only has 1200 miles on it and looks like new.Bill
I have a 1978 puch newport that is oil injected with a factory plastic oil tank on the rear. It has no clutch lever on the handle bars. Can anybody tell me about this style puch. I have had many puchs over the years but no injected e50 engines.
A fellow moped enthusiast had his 1980 pa 50 honda moped stolen and vandalized. He wants to look at another bike as they cut his wiring. He lives in Marblehead mass. Does anyone in the area have a 1980 pa 50 he could look at. I have a nice 1983 but I think the wiring is not the same.thanks
What other engine will bolt up to an intramotor gloria moped. I have a cool old looking bike and want to get it on the road. The current engine is no good (seized hard) and I want to replace it. I was thinking a garelli might fit but don't know. Has anybody had any experience doing this?Thanks Bill
Does anybody know where I can buy a new fuel valve for my puch AD moped? It's an inline valve that mounts in the side of the moped with 2 lines in and 1 line out to carb.Thanks
I have a 1981 motobecane with mag wheels. It's missing the gear and rear brake hub. Will the gear and brake hub from a 1977 spoke wheel be the same?Bill
I just want to ask if anyone knows of a good Honda scooter repair site. I am trying to get a honda aero 50 running.
I changed out my the ignition and it runs great. Thanks to those who responded.
I have a garelli moped with power to the coil but no spark.Any ideas?
I have an old peugeot 103 that I am going to try and get running. I want to know if there is a different carb I can swap onto this bike. I have not had much success cleaning the carbs that are on these bikes before.Thanks
What is the easiest way of cleaning a maxi gas tank. It's not all crusty but the fuel is turning brown after sitting for a awhile( month). This means to me rust.
I have a 1980 yamaha qt 50 with poor spark. I recently bought and installed a new battery. The bike will not start. I have never had the bike running (bought it this way). What do I look for and how easy are parts to obtain?Thanks for any help.
I have a sachs engine on my moped and can't get it to idle right. I read on here somewhere that the correct point gap for motoplat ignition is .040. This seems way too much. Does anyone know the correct gap for the points on this thing?Thanks
Sparta moped, It starts and runs but won't idle. It will need some work to get it running right. Pick up only no shipping.Email firstname.lastname@example.org$400 cash
I have a few bikes that I can't get to idle at all and I am wondering if it could be the cranks seals. I don't know how to tell if that's the problem. One is a sparta with a sachs engine with 1200 miles on it. The other is a peugeot 103 with about 700 miles on it. Neither bike will idle at all. They run fine going down the street once you get them going. I have cleaned the carbs alr
I can get the engine to spin over but the bearings are real loud. It was frozen up when I bought it and I tapped the flywheel to get it to spin. So does anyone sell a total rebuild kit and how much? Do I need a press to get it apart or to put back together.
How difficult is it to rebuild a puch 2 hp, 2speed engine?What tools are needed and what is the average cost?Has anyone done this recently?Where is the best place to buy all the parts or a kit?Thanks for any help or tips
Check the tail light bulb to make sure it's good. On some of these old bikes the ignition is wired through the tail light.
I have a real low mileage peugeot 103 that won't idle but runs good once you are moving. I think it needs a new carb. I already cleaned it out. What could I swap it out with?
Call Handy bikes in columbus Ohio. Ask for Bob Jones and they are a hero/panther dealer.
I have a 1980 vespa grande that stalls when brake is applied or for no reason. i have cleaned and adjusted the points, cleaned carb and idle jet, swapped coil, plug and plug cap. the brake light bulb is good. What could I be missing?
vespa mopeds have an idle jet that is a built in passage way in the carb. Zippy told me about it and it helped me alot. He can explain it better than I can. He actually emailed me the fix, goodluck
What holds the pedal arm onto the shaft on the sprocket side of a puch? There is no tapered pin on it.
Will the engine off my puch magnum bolt up and work on my maxi?Thanks
Does anyone know if a puch cobra and puch magnum have the same fuel valve?
Where can I get new float caps and float for my Batavus?Thanks
I need a garelli and a puch maxi engine to repair my mopeds in the boston area.thanks
I have a few tomos sprint and want to clean out mufflers. What is the best method?