Results 1–30 of 170
george boardway — 5 years ago
she it to me in Portland or can you make TREATLAND MOPED PARTS it looks like a lot of good stuff
george boardway — 6 years ago
by the polinoni carb spiget have them weld then machine your case treats or 1977 can get you one special order
george boardway — 6 years ago
12 mm rist pin I just bored a Honda aytusa cylinder to 46 there 44 stock the Honda has a 10mm pin 1977 has a 12mm rod kit for Honda that slug will work and if you buy the adapter 1977 and treat you can run a kx 80 read vavle and id you own an express hang on it will run with the big wheel guys
george boardway — 6 years ago
dam still got the g2 I made adapeters for the pedal shaft so you can use vespa grande bushings got to take the flywheel off to replace the sprocket key to see if its not seized she said eric sabitinoe sabitinoe just rebuilt it boy I wish she would have came back after it some one stoled the muffler so its getting an expansion chamber and some richer jets
george boardway — 6 years ago
still got the odyssey the more I look at it the more I want to dump the odyssey engine looks like 1977 has a puch motor mount that would weld to the frame I could do away with the belt and spring set up cheaper more plentiful puch parts tons of e50 engines very dependable
george boardway — 6 years ago
sub frame grande
george boardway — 6 years ago
how much shipped usa my email geoboardway@outlook.com
george boardway — 6 years ago
ive got one what we talking price / but first what kind of chassi do you want to put it in
george boardway — 6 years ago
sorry but o also have the k10 forks nothing to brag about but the rusty tank is pretty bad to bad its not a za engine
george boardway — 6 years ago
are you parting it out 75.00 for a good puch frame pinto maxi just one that's not rusted out /or bent
george boardway — 6 years ago
also had that problem with a CDI case used a beer can silicone to get it to work measured the pipe it was 15mm instead of 16mm
george boardway — 6 years ago
had that same problem carburater bushing I now replace them and silicone the slit at the top / if it starts then runs then dies check your carb vent but its usalley a stuck float needle replace with treats spring needle/ use the ones with the red tip ive had the black tip ones break off and stop the fuel
george boardway — 6 years ago
my favorite treat pipe so far for fit and performance works better that the high dollar pipes
george boardway — 6 years ago
rear brake cable 1982 nc 50 express
george boardway — 6 years ago
still got them that Suzuki front fork looks great
george boardway — 7 years ago
vespa grande you will have to drill one hole higher and it looks great to like it came from the factory
george boardway — 7 years ago
try the carb bushing make sure your not sucking air scored pistons suck
george boardway — 7 years ago
I use lucas because the auto parts store carrys it and its one block from my house but when I go across town I buy stihl ful synthetic that's the silver bottle my moped runs really good with the stilh and so does my weed wacker stihls my number one choice at 50cc I can afford to run cheap oil or lose any power
george boardway — 7 years ago
buy a new one 16.00 at moreys mopeds in fullerton California ive personally f-cked up two of them trying to get them off but they have the different sizes 9.6 to 10.5 moreys /shawn is also a moped guru and can save you a fortune in broken parts and frustration
george boardway — 7 years ago
see if a brake shop can reline your clutch / but its a great time to upgrade roller rod big bore / yes diller dollar dan this thing can be faster and super reliable /and great fun now get on it
george boardway — 7 years ago
vespa ciao clutch fits a trf / belts / go to the auto parts store /there about 4dollars the oem was 31.00 /vespa ciao starter shoes fit trf clutches and treat or fatcity or 1977 the kinetic carb the 13 13 carb will fit but put a new bushing in so it seals the stock 45 main jet should be replaced I drilled out a kinetic carb with a 1/2 inch bit cleaned it good ran a 58 main and a technogas pipe
george boardway — 7 years ago
got a solo open road and new engine some lady in Nebraska has a whole whare house ful of them new engine only cost 69.00 but I bought for a project I bought a polini water pump and a dirtbike radiator the previses owner said it ran till it got hot and then it quit and he would fill it up with water again and ride around till it got hot so I'm going to go all out how big can I bore what kind
george boardway — 7 years ago
my vespas I found a great replacement rim 1977 has a moto became 17 - 28 spoke rim I sent it to Buchanan they redrilled and dimpled the rim I have 10 guage stainless spokes on my ciao front wheel its awesome / some asshole or f-cking retard switched headlights on my ciao I run a 12volt kinetic lighting coil with a 13.00 yellow red wire puch regulater and a 4411sylvania from orieleys auto parts it
george boardway — 7 years ago
got a brand new never ran solo and a polini waterpump kit and a radiator like yours its a open roads but I also have that after cooler exhaust
george boardway — 7 years ago
my email micro soft changed its now geoboardway@outlook.com it really pissed me off need some ciao floor board tabs thank you and if any ones got some spares let me know
george boardway — 7 years ago
what do ya want for the za parts my email is geoboardway@outlook.com it was Hotmail but Microsoft changed it for security / but I think the but heads where after my moped parts
george boardway — 7 years ago
during the ice storm I rode my moped to work it starts super easy and has super bright lights im using a stock piaggoe flywheel early style for points the later style has a full magenet and smaller coils the pinnaso flywheel I got from treat and I wish they would get more cause they will work with kinetic trf cdi and if your kinetic has a bad keyway or wobbles out there is no way to fix it at
george boardway — 7 years ago
the kinetic lightining coil they use varnish /so when you crimp a wire end it doesn't get a good conettion the head light is a sealed beam from oriellys auto parts for a garden tractot sylyania 4411-1 my tail light is a 3.00 ebay led also my horn is stock vespa and its loud I tried a after market 12 and you got to rev the engine to get it to work so use the stock horn / treat sells th
george boardway — 7 years ago
got a solo want to buy it its got there after burner muffler
george boardway — 7 years ago
broke but treat would love them / if I had the doe id get them all any brothers in the area help him / much needed to keep others rolling best wishes in sack I hope you do super well george