Results 1–30 of 1730
Yeah and you guys can start fresh with all the f****** s*** that I've done all these years of f****** gone wasted and you all f****** know so I'm done I'm not being a part of this f****** s*** f****** website you guys all created instead of what was supposed to happen
I found on mass.gov you don't need a title!
Just looking for a friend thanks!
Does anyone know how to get a title from Massachusetts for a moped with no title?
Throw some mystery roll down that spark plug hole and let it sit there for a little while if it seems to be locked up just means that your piston rings are stuck in the cylinder wall by oxidation. After a couple days just keep soaking it keeps choking that you're going to have you might want to remove the engine from the chassis. It only takes a few moments and then you can really work on it
This is a 1976 motobecane Moby that is all original minus the original carburetor and intake. Has the banana expansion chamber all cables are intact and working and in good shape. New spark plug. Not a bad little machine in fact it does 32 miles per hour and I'm 220 lb.
Are you putting it on M48?I have a 12 mm Square Bing ready to go if you need it just pay shipping
I had a really good idea for my QT50 project back in the day. My idea was to remove the gas tank from the frame run a bar like a top tank and run it like a top tank it'll be nice and low to the ground and I think would look really cool. Good job with your build but I like your exhaust
Good Looks Mopedlar.Nice guy eh?!
LOL I screenshot of the whole website if they want it though just hit me up. Let me know man
There might be a pujo pardon there by accident I was probably too tired and I was looking for the a V10 polini cases. Anyone who can wrap your brain around this idea just made myself a reference so when I go to build my motobecane I'll have all the parts that I want thought I would share it because it seems like an easy way to go through all the parts. I actually downloaded the entire treats
If you running 80 CC or higher you're going to want to use like a vm20 or a polini c p series for a carb.If you want to look Semi stock go for an m l m pipe but I would recommend hacking welding like a circuit proma exhaust or a ninja G3 exhaust you can find them anymore or maybe even a side bled esterel always works well
What a nice little design
Well could tell first how long you ran the machine that leanYou should take your spark plug out and take a picture of the electrode so we can see it
Crazy spark.Ran then died then ran then died.Checked decompChecked HeadgasketChecked needle valveChecked filterChecked carb jetMaybe cyl toast
Drill it out ya have a 13.5mm.....caution as wall can walk
Looks like a mild upgrade from the stock 50 yeah nothing too fancy here looks like just do boarded you know case inductive is Chichi $50 I think this would be a nice little upgrade something to get you probably closer to 40 45 miles an hour I know a little bit more acceleration that would be great
I am in southern NH willing to work with you on a yellow motobecane that needs a good home
Sell it it's a f****** junk
This should be in Performance
Just to let you know all you nubes out there was talking about this no ped..... this bike needs a PW50 pinion rear axle shaft so you can have a higher gear ratio 4 better top end
Please disassemble your intake and check your Reeds for any rust as they might break off being that old and cause damage to your motor
I have a 1976 motobecane mobylette with malossi intake 12 mm Sha carb. It has the small expansion chamber banana exhaust. 32 miles an hour new petcock new fuel line new intake gaskets all lights work cables work wonderfully speedometer works and lights up
Want to keep your bike looking stock while still increasing your air flow fuel flow with a simple plug-and-play solution that will fit any Puch or Sachs intakes! With the magura throttle cable you can swap out a carburetor and under 10 minutes. I do have other Jets available for whatever displacement!Do not be intimidated by other people telling you that this is not a good carburetor what they