Results 1–30 of 31
yeah i tried spraying wd40 oo the cylinder and the intake and it didnt effect the idle
Ok so i have a magnum with a za50 on it. It has a stock 2hp cylinder, pipe, etc with a bing 15 carb and a 14 intake. I have set the timing as best as I can have good compression and have cleaned everything possible. The problem is that with a reasonable jet in the carb 58-62 the bike only runs well when choked about halfway, if not it gets bogged down from about half up to wot. Now if I put a
So i'm trying to change my tire tubes and have now punctured 3 in a row. The tire is the correct size but is mighty hard to get on again... I mean like full on sweat pouring down my face. Any ideas/advice?
ive tried fully open, choked, idle, and everything between. I think its time to take start from scratch again.
so yeah... i put the plastic sleeve with rings back and the points are cleaned and gapped. What jet would you put on a stock magnum engine with a 12 intake and a 15 bing carb? Ive been trying 58-62 could this be the problem? Thanks
So I have a magnum that I got in the winter and just got to working on it. Ive cleaned it all up, hardwired it, new plug, new carb, new piston rings. It had an oil injector on the za50 but I removed the mechanism and covered it with a piece of aluminum. Basically the ped will kick but not turn over and if i keep pedaling it will keep kicking but never enough to run on its own. Ive checked the
Looking for a pinto 2 complete or frame and tank
Looking for a small vintage honda in the new york area but will consider shipping. ss50 cl50 cl70 cl90 or something similarThanks
Any pinto 2 tanks out there?
Ok shoot me offers for my yellow rigid frame. No obvious dents but has a few tics of rust and the tank needs cleaning. Includes fork and spoke wheels. This is a rare yellow rigid never seen one before. Will trade for pinto/swinger frames in good condition. I'm in NYC, the closer to me the better.
So I have a Maxi N rigid that is yellow, not a repaint, possibly an import. The tank needs to be cleaned out (rusty but not too bad) besides that it is good. no dents on the frame but some rust on the handle bars and the seat is crappy. Needs grips and new cables, brakes work fine. I put a clean running e50 on it with the 2hp stock cylinder and a 14 bing (you can have the original cylinder if yo
looking for a working e50 (or za50 maybe) engine have cylinder head and pistonalso looking for a 15 bing with filter hopefully,two 14mm intakes,a puch triple tree with clamps for barscafe barsand a rear 17" puch wheel with hardware (any style)Thanks
anyone? snowflakes? I'll buy the set if i have to
Looking for a rear wheel for my Magnum. Mag, spoke whatever I just wanna get riding again before its too late. I'm needing the hardware as well, especially the nuts. Drop me a line thanksKurt
Summer is half over and my bike is still sitting on the street dead. I dont have the time to do a full rebuild on my current engine so I'm looking for a running, tuned complete za50 that i can just slap on my bike and go. I can do E50 as well but prefer that two speed. Tell me what ya got.
looking for a rear wheel for my magum im in nyc so local would be nice
Looking for a za50 for my magnum (dont need cylinder/head) in nyc area hopefully.
looking for the large gasket not the transmission cover gasketthanks
thanks guys yeah its for a magnum II no oil injection
just looking for a za50 case i really only need the clutch side but will take what i can get
looking for some 16" snow-queens or mag-pies for my garelli ssxli'm in Brooklyn so local would be nice but the mail ain't bad either
I have a 78 ssxl and I'm looking for a new triple tree
im looking for a reed to match this garelli kithttps://www.1977mopeds.com/product/177/Garelli-70cc-Polini-Reed-Kit/you can see by the gaskets that its on the small side and is a two screw not fourthanks for the help
have a super sport xl and want to add a 70cc kit to it... used or new
I'm looking for a rear garelli wheel for my super sport xlmag or spoke
Well i stripped the screw then drilled out the head cracked the case open and tried using a stripped screw tap... it is stuck for goodIn the pic (not of my case) its the hole that has the sleeve on the far rightdo you guys think it will screw tight enough?anyone have a case they want to sell me