I’ve done some research and I’m pretty sure that I’d rather not stick it in a fire! Should I use bottle brushes w degreaser, is it ok to use a power washer at a car wash, does the end of the exhaust come off? It’s looking pretty crusty and I’d like to clean it so please help me out...
EXHAUST CLEANING for a Puch Magnum Mk2
Re: EXHAUST CLEANING for a Puch Magnum Mk2
Lossen the front clamp and mount it'll slide off. Don't loose the rubber bootie! Loosen the nut at the end and the doodle will come off. Filler up with a couple spray cans of oven cleaner and wait 24hrs. The bring it to the carwash if you don't have a pressure washer and sprayer out.
Fire is great tho.
Re: EXHAUST CLEANING for a Puch Magnum Mk2
Which clamp?
Re: EXHAUST CLEANING for a Puch Magnum Mk2
There is only one clamp. The one that attaches it to the header pipe.
If not post pictures it might have a different pipe from a previous owner.
Re: EXHAUST CLEANING for a Puch Magnum Mk2
Here’s you go
Re: EXHAUST CLEANING for a Puch Magnum Mk2
Remove the end cap by removing the 10 mm nut on the inside of it and bang it off with glancing blow’s at seam with a rubber mallet
You may have to heat it up a bit at the end because it may be stuck due to harden oil deposits then you can clean inside it
Re: EXHAUST CLEANING for a Puch Magnum Mk2
I'm a fan of the nuts and bolts on a wire shoved into a drill Chuck and let it rip
Re: EXHAUST CLEANING for a Puch Magnum Mk2
I did what I could and put it back on, the only thing is that when I put it back on it’s a little loose, it rattles, very little but I think it might be normal?
Re: EXHAUST CLEANING for a Puch Magnum Mk2
Looks like you lost the rubber bootie. You can make a new one with a silicone baking sheet from the dollar store. I've even used a bicycle inner tube on a pinch... Or post In buy/sell, I'm sure someone knows where to get one.
Re: EXHAUST CLEANING for a Puch Magnum Mk2
> Aaron Blair Wrote:
> -------------------------------------------------------
> Looks like you lost the rubber bootie. You can make a new one with a
> silicone baking sheet from the dollar store. I've even used a bicycle
> inner tube on a pinch... Or post In buy/sell, I'm sure someone knows
> where to get one.
It’s not rubber it’s a asbestos gasket but I don’t like to try to put a new one even though you should be able find one on ebay because scraping off or grinding out the old one to get the new one to seat correctly is very dangerous. I just wrap aluminum foil around the header to make it tight/good seal
Re: EXHAUST CLEANING for a Puch Magnum Mk2
^^^^ whell shit, Ken's method sounds alot cheaper and easier for sure! Wish I thoutta that one.
Re: EXHAUST CLEANING for a Puch Magnum Mk2
Slice up a beer can for shims
Layer pieces of paper gasket/alu
Clamp the piss out of it
Oil will soak paper and it will swell
No leak
Works as a carb shim when your bing falls off outside town
Ask me how I know
Also my favorite shim when your wrench is too big for a nut
Beer can shim inside socket too!
Convert your favorite standard wrench to metric with oneeasystep
You just have to drink the beer first
Re: EXHAUST CLEANING for a Puch Magnum Mk2
> Kevin Bishop Wrote:
> -------------------------------------------------------
> You just have to drink the beer first
Or snag that can out of the ditch . ;)
« Go to Topics — end of thread
Want to post in this forum? We'd love to have you join the discussion, but first: