Re: WTB Motion Pro m6 Stud Installer

* * /
This single post is part of a larger thread. Start from the top or view this post in context.

> Dirty30 Dillon Wrote:

> -------------------------------------------------------

> > Rocco Taco Wrote:

>

> > -------------------------------------------------------

>

> > “In the majority of cases, screw the studs into the block FINGER-TIGHT

>

> > ONLY, or with a very slight amount of pre-load (specific manufacturers

>

> > may recommend as much as about 8 to 10 ft.-lbs. of pre-load). Do not

>

> > double-nut the stud and tighten severely. Remember — the torque value

>

> > given for the installation refers to the tightening of the nut only,

> not

>

> > the stud itself!”

>

> What are you quoting?

>

> Earlier you hypothesized that people who bottomed out their studs were

> snapping them because they weren't leaving "room for the stud to screw

> in."

What makes you think I retracted that statement? We just see it two different ways. The lock tie is cool ( i like to let it dry on the stud first)

Well fuck I don’t think it matters that much if you prefer to pre-torque the studs ether way they are going to get torqued down to the same depth

This single post is part of a larger thread. Start from the top or view this post in context.
Subject Written By Posted
  WTB Motion Pro m6 Stud InstallerTopic by: Sean Daugherty Sean Daugherty 01/16/20 04:33PM
  Re: WTB Motion Pro m6 Stud InstallerRe: MPB Andyrew MPB Andyrew 01/16/20 04:36PM
  Re: WTB Motion Pro m6 Stud InstallerRe: Mike Boyd Mike Boyd 01/16/20 05:48PM
  Re: WTB Motion Pro m6 Stud InstallerRe: Sean Daugherty Sean Daugherty 01/16/20 08:28PM
  Re: WTB Motion Pro m6 Stud InstallerRe: Dave Steele Dave Steele 01/16/20 05:10PM
  Re: WTB Motion Pro m6 Stud InstallerRe: * * * * 01/16/20 05:37PM
  Re: WTB Motion Pro m6 Stud InstallerRe: Sean Daugherty Sean Daugherty 01/16/20 08:33PM
  Re: WTB Motion Pro m6 Stud InstallerRe: * * * * 01/16/20 09:03PM
  Re: WTB Motion Pro m6 Stud InstallerRe: Sean Daugherty Sean Daugherty 01/17/20 09:12AM
  Re: WTB Motion Pro m6 Stud InstallerRe: ♣Slew Foot♣ ♣Slew Foot♣ 01/18/20 08:47AM
  Re: WTB Motion Pro m6 Stud InstallerRe: Richard Eberline Richard Eberline 01/16/20 07:01PM
  Re: WTB Motion Pro m6 Stud InstallerRe: Terbo Speghetti Terbo Speghetti 01/16/20 07:23PM
  Re: WTB Motion Pro m6 Stud InstallerRe: Richard Eberline Richard Eberline 01/16/20 07:40PM
  Re: WTB Motion Pro m6 Stud InstallerRe: Dirty30 Dillon Dirty30 Dillon 01/17/20 09:59AM
  Re: WTB Motion Pro m6 Stud InstallerRe: Sean Daugherty Sean Daugherty 01/17/20 11:40AM
  Re: WTB Motion Pro m6 Stud InstallerRe: Dirty30 Dillon Dirty30 Dillon 01/17/20 11:44AM
  Re: WTB Motion Pro m6 Stud InstallerRe: Sean Daugherty Sean Daugherty 01/17/20 11:46AM
  Re: WTB Motion Pro m6 Stud InstallerRe: Angry Hipster Angry Hipster 01/17/20 02:29PM
  Re: WTB Motion Pro m6 Stud InstallerRe: * * * * 01/17/20 02:47PM
  Re: WTB Motion Pro m6 Stud InstallerRe: * * * * 01/17/20 02:25PM
  Re: WTB Motion Pro m6 Stud InstallerRe: Dirty30 Dillon Dirty30 Dillon 01/17/20 02:54PM
  Re: WTB Motion Pro m6 Stud InstallerRe: * * * * 01/17/20 03:17PM
  Re: WTB Motion Pro m6 Stud InstallerRe: Dirty30 Dillon Dirty30 Dillon 01/17/20 03:57PM
  Re: WTB Motion Pro m6 Stud InstallerRe: * * * * 01/17/20 04:49PM
  Re: WTB Motion Pro m6 Stud InstallerRe: ***Kim Jong illest*** ***Kim Jong illest*** 01/17/20 05:34PM
  Re: WTB Motion Pro m6 Stud InstallerRe: josh n josh n 01/18/20 12:26AM
  Re: WTB Motion Pro m6 Stud InstallerRe: river 2strokes river 2strokes 01/19/20 05:22AM
  Re: WTB Motion Pro m6 Stud InstallerRe: Sean Daugherty Sean Daugherty 01/19/20 12:14PM
  Re: WTB Motion Pro m6 Stud InstallerRe: ♣Slew Foot♣ ♣Slew Foot♣ 01/19/20 07:29PM
  Re: WTB Motion Pro m6 Stud InstallerRe: Overpriced Parts Overpriced Parts 01/19/20 02:37PM
  Re: WTB Motion Pro m6 Stud InstallerRe: Dirty30 Dillon Dirty30 Dillon 01/19/20 02:41PM
  Re: WTB Motion Pro m6 Stud InstallerRe: * * * * 02/02/20 10:58PM

Want to post in this forum? We'd love to have you join the discussion, but first:

Login or Create Account